思科 微軟 IBM HP認證考古題PDF下載

免費087-301考古庫Demo賞析

Pass4Side官方網站最新的087-301考古庫詳細信息

免費087-370考古庫Demo賞析

Pass4Side官方網站最新的087-370考古庫詳細信息

免費087-070考古庫Demo賞析

Pass4Side官方網站最新的087-070考古庫詳細信息

免費087-170考古庫Demo賞析

Pass4Side官方網站最新的087-170考古庫詳細信息

免費086-470考古庫Demo賞析

Pass4Side官方網站最新的086-470考古庫詳細信息

免費4A0-106考古庫Demo賞析

　
　
Exam : Alcatel Lucent 4A0-106
Title : Alcatel-Lucent Virtual Private Routed Networks

1. When a Service Provider offers VPRN services to its customers, which of the following functions are expected to be the responsibility of the Service Provider? (Choose three)
A. Distributing the customer generated labels between sites
B. Distributing the customer routing information between sitesDistributing the customer? routing information between sites
C. Forwarding the customer originated data packets to the appropriate destination
D. Forwarding the provider originated data packets to the appropriate customer site
E. Providing secure layer 3 routing exchange between sites
Answer: BCE

2. What are the main functions of a Layer 3 VPN? (Choose three).
A. Distributing customer routing information between sites
B. Forwarding customer data packets
C. Providing an integrated billing solution
D. Maintaining separation between distinct customer networks
E. Allowing the implementation of Layer 3 devices in the provider core
Answer: ABD

3. Complete the following statement. In a VPRN, the label signaled by RSVP-TE is used to ____________________.
A. Identify the egress PE in the MPLS domain
B. Signal the egress VPRN ID
C. Identify the ingress PE in the MPLS domain
D. transport route updates between PEs
Answer: A

4. In a VPRN the PE device is configured to run which of the following protocols? (Choose three.)
A. MP-BGP for exchanging customer routes with other PEs
B. A routing protocol for exchanging customer routes with the CE
C. MPLS for exchanging labels with other provider core devices
D. MPLS for exchanging labels with the CE devices
E. Targeted LDP for exchanging VPRN labels with other PE devices
F. A label signaling protocol for defining transport tunnels between PE and CE devices
Answer: ABC

5. Complete the following statement. In a VPRN, the inner label is used to ____________________.
A. Identify the customer network on the egress PE
B. Establish the LSPs between PE devices
C. Identify the egress PE in the MPLS domain
D. Identify the customer network on the ingress PE
Answer: A

6. What operation is performed by a P device on the label signaled by MP-BGP when it receives a labeled packet for a VPRN service?
A. It will label switch the packet based on this label
B. It will decrement the TTL and label switch the packet based on this label
C. It will SWAP the label for a new label and then label switch the packet
D. The P router does not perform any operation on this label
Answer: D

7. Which protocol is used to exchange customer VPRN routes between PE devices?
A. OSPF
B. ISIS
C. MP-BGP
D. BGP
E. Targeted LDP
Answer: C

8. Which of the following statements is true? Choose the best answer.
A. A P router may forward customer packets to their destination without the presence of a route to that destination
B. The ingress PE router may forward customer packets to their destination without the presence of a route to that destination
C. The egress PE router may forward customer packets to their destination without the presence of a route to that destination
D. Any provider core router (P or PE) may forward customer packets to their destination without the presence of a route to that destination
Answer: A

9. What are the two primary problems the service provider must consider when providing traditional Layer 3 VPN services using only a single common routing table in the provider core? (Choose two)
A. Memory exhaustion in the provider core
B. Route leaking between the customer networks
C. CPU utilization for route processing
D. Unwanted packet forwarding between customer networks
Answer: BD

10. Choose the answer that best completes the following sentence. The CE device is typically configured with ___________________________.
A. A single routing protocol for exchanging routes with both the internal customer routers and with the PE
B. MP-BGP to exchange routes with the PE.
C. MPLS and a routing protocol for the exchange of labels and routes with the PE
D. MPLS for exchanging labels with other CE devices
E. A routing protocol for exchanging routes with the internal customer routers and a routing protocol for exchanging routes with the PE
Answer: E

11. Which of the following statements are true regarding P devices in an MPLS VPRN? (Choose two.)
A. Participate in service provider core routing
B. P devices are not required to be MPLS enabled. MPLS is only required on the PE devices
C. Run a common routing protocol with the CE router
D. Must support MP-BGP
E. Do not have any connections to the CE
F. Must be aware of the VPRNs
Answer: AE

12. Which of the following terms also correctly describes a Layer 3 VPN? (Choose three)
A. VPRN
B. BGP/MPLS VPN
C. VLL
D. VPLS
E. IP-VPN
F. ePipe
Answer: ABE

13. In a traditional layer 3 VPN which of the following will be an issue when there is overlapping address space between two customers? Choose the best answer.
A. There will be increased memory usage on the PE
B. There will be increased CPU utilization on the PE
C. The CE will reject the overlapping prefix
D. The PE will not recognize the prefixes as being different
E. There is no issue with overlapping address space in a traditional Layer 3 VPN
Answer: D

14. Which of the following devices would typically have VRF instances?
A. Any CE device
B. Any PE device
C. Any P device
D. Any router in the service provider core
E. Any customer router
Answer: B

15. Complete the following statement. In a VPRN, the label signaled by RSVP-TE is used to ____________________.
A. Identify the egress PE in the MPLS domain
B. Signal the egress VPRN ID
C. Identify the ingress PE in the MPLS domain
D. transport route updates between PEs
Answer: A

免費下載4A0-106考古庫Demo

Pass4Side提供最新的Alcatel Lucent認證 4A0-106考古庫，其全名為：(Alcatel-Lucent Virtual Private Routed Networks). 在您決定是否購買之前 可以先下載4A0-106考古庫的部分演示. Pass4side是全球唯一提供所有IT認證考試考古庫demo免費下載的廠商 ，以下為免費4A0-106模擬測試題的下載鏈接

免費的4A0-106考古庫PDF下載鏈接

免費4A0-109考古庫Demo賞析

　
　
Exam : Alcatel-Lucent 4A0-109
Title : Alcatel-Lucent Triple Play Services

1. Which answer best completes the following statement. Over the multicast VPLS, ___________ traffic flows in the ______________ direction.
A. Multicast data, Upstream
B. Multicast data, Downstream
C. Multicast data, Upstream and Downstream
D. All, Downstream
E. IGMP, Downstream
Answer: B

2. Choose the best answer to complete the following statement. Ethernet frames transmitted by the RG contain:
A. 802.1Q VLAN ID of zero and 802.1P priority bits of all zero
B. 802.1Q VLAN ID randomly assigned by the RG and 802.1P priority bits of all zero
C. 802.1Q VLAN ID of zero and 802.1P priority bits randomly assigned by the RG
D. 802.1Q VLAN ID of one and 802.1P priority bits of all ones
E. 802.1Q VLAN ID of zero and 802.1P priority bits as assigned by the application
Answer: E

3. The Alcatel 7342 P-OLT is a device that:
A. Is located in the CO that terminates the outlying ONT’s
B. Is located in the subscriber home that interfaces to the RG
C. Is located in the subscriber home that connects to the PSTN
D. Is located at the SAI that aggregates DSL lines
Answer: A

4. The internal BSAN architecture is composed of which of the following?
A. Line Termination (LT) portion and a Network Termination (NT)
B. Link Termination (LT) portion and a Node Termination (NT)
C. Link Termination (LT) portion and a Network Termination (NT)
D. Line Termination (LT) portion and a Node Termination (NT)
Answer: A

5. The Alcatel 7302 ISAM is typically located in:
A. The customer home
B. The Serving Area Interface (SAI)
C. The provider Central Office (CO)
D. The video headend
Answer: C

6. True or False. The RG is typically provider managed in Triple Play Services?
A. True
B. False
Answer: A

7. Which technical development allowed the deployment of IP protocol features at any point in the network?
A. The invention of ATM
B. The IP enabling of the DSLAM
C. The usage of IP in the home network
D. The usage of an IP enabled BSA
Answer: B

8. Which of the following may be connected to the RG in the subscriber home network? Choose the best answer.
A. P.C.
B. TV with STB
C. Gaming console
D. LAN switch
E. Any Ethernet connected device
Answer: E

9. What are the minimum requirements for the Residential Gateway? Choose 2.
A. NAT support
B. Support Routed and bridged mode
C. Multicast (IGMP) support
D. Support IP packet filtering
E. Be able to terminate multiple access mediums
Answer: AC

10. Which in home wiring standards are suitable for delivery of Triple Play services?
A. Ethernet over Category 5
B. Multimedia over Coax Alliance (MoCA)
C. Home Phone Networking Alliance (HPNA) v3
D. Category 3 wiring
Answer: ABC

11. Which of the following is not a TPSDA network zone?
A. Home
B. Broadband Access
C. Broadband Aggregation
D. Broadband Metro
E. IP Services Edge
Answer: D

12. Why does the RG operate as a DHCP server?
A. As a local backup in case the provider DHCP server is unreachable
B. The subscriber may choose to manage their own IP addresses
C. The RG will never operate as a DHCP server
D. To assign IP addresses to the internal home devices when operating in routed mode
E. To assign IP addresses to the internal home devices when operating in bridged mode
Answer: D

13. The Broadband Service Access Node (BSAN) may be:
A. The Alcatel 7330 FTTN ISAM
B. The Alcatel 7342 FTTU ISAM
C. Neither (a) or (b)
D. Both (a) and (b)
Answer: D

14. Why is the DHCP relay agent required?
A. DHCP broadcasts requests will not leave the local subnet by default
B. It allows the modification of DHCP messages to include provider specific parameters
C. It increases the security of the TPSDA
D. It allows the modification of DHCP messages to include subscriber management parameters
E. All of the above
Answer: E

免費下載4A0-109考古庫Demo

Pass4Side提供最新的Alcatel Lucent認證 4A0-109考古庫，其全名為：(Alcatel-Lucent Triple Play Services). 在您決定是否購買之前 可以先下載4A0-109考古庫的部分演示. Pass4side是全球唯一提供所有IT認證考試考古庫demo免費下載的廠商 ，以下為免費4A0-109模擬測試題的下載鏈接

免費的4A0-109考古庫PDF下載鏈接

免費4A0-110考古庫Demo賞析

　
　
Exam : Alcatel-Lucent 4A0-110
Title : Alcatel-Lucent Advanced Troubleshooting

1. L1 ISIS adjacency is up between two routers (Node-1 and Node-2) with MD5 authentication configured. During a maintenance window, an operator was planning to change one of the ISIS hello authentication key from admin to admin123. After removing the hello authentication key from Node-1 (no change on Node-2 side), the ISIS adjacency stayed up. The operator decided to fall back to the original configuration and called Alcatel for support.
Which of the following statement best describe the cause of the problem? Select one answer only.
A. The ISIS hello authentication key was not configured properly in the first place, that’s why removing the authentication key does not impact the adjacency
B. The ISIS authentication key is the same as the hello authentication key, therefore removing hello authentication key does not impact the adjacency
C. The system interface is missing from the ISIS configuration, therefore ISIS is not working properly even before the change
D. ISIS hello authentication key is only used for hello packet exchange. It does not affect ISIS adjacency
E. ISIS hello authentication key is not used to bring up ISIS adjacency when traffic-engineering is enabled on the routers
Answer: B

2. Which of the following debug statements can be used to troubleshoot if the OSPF adjacency is staying at xstart state? Select two answers.
A. debug router ospf rtm
B. debug router ospf packet dbdescr
C. debug router ospf neighbor
D. debug router ospf packet hello
E. debug router ospf spf
Answer: BC

3. Two routers are physically connected to each other over Ethernet port 1/1/ Review the configuration information shown below. What state should the OSPF neighbor be in?
A. INIT
B. EXCHANGE
C. EXSTART
D. FULL
E. No OSPF neighbor
Answer: E

4. Based on the following configuration, which of the following statements are true? Choose all that apply.
A. No OPSF adjacency found on Node 1
B. Full OSPF adjacency between Node-1 and Node-2
C. Full OSPF adjacency between Node-1 and Node-3
D. Full OSPF adjacency between Node-1 and Node-4
E. OSPF is enabled on Node 1
Answer: BE

5. Two routers are physically connected to each other over Ethernet port 1/1/1. Review the configuration information below. What state should the OSPF neighbor be in?
A. INIT
B. EXCHANGE
C. EXSTART
D. FULL
E. No OSPF neighbor
Answer: D

6. The LDP session is not down between Node-1 and Node-2. Based on the following configurations, what is the cause of the problem?
A. LDP targeted-session is enabled with no service configured
B. OSPF adjacency is not up between Node-1 and Node-2
C. Router id is not advertised by OSPF
D. LDP is disabled on Node-1
E. Traffic-engineering is not enabled on Node-2
Answer: C

7. Two direct connected routers are running RIPv2, neighbors are up but there is no route in the RIP database. Review the configuration information below. What is the potential problem?
A. System interface is not added to the RIP protocol
B. No import policy is configured
C. No export policy is configured
D. Split-horizon has to be disabled in RIP
E. Message-size has to be configured with a non-zero value
Answer: C

8. What are the typical RIP related issues found during troubleshooting?
A. Interface filters
B. Broadcast/Multicast mismatch
C. Area id not match with neighbor
D. Group name not match with neighbor
E. Hop count too high
Answer: ABE

9. Two routers are physically connected running ISIS. ISIS L2 adjacency is up and running but L1 adjacency is not up. Review the configuration information shown below:
Which of the following statement best describe the cause of the problem? Select one answer only.
A. The ISIS interface level is not configured on both routers
B. The ISIS interface type should be configured as point-to-point interfaces
C. ISIS System IDs are not configured on both routers
D. ISIS Area addresses are not configured on both routers
E. ISIS level capacity are not configured on both routers
Answer: D

10. Two routers are physically connected to each other with ISIS configured. No ISIS adjacency can be found on both routers. Ping works fine on the local and the remote interface addresses on both routers. Review the confguration information shown below.
Which of the following statements best describe the cause of the problem? Select one answer only.
A. The ISIS interface level configured does not match the ISIS level capability supported on the routers
B. The ISIS authentication check is enabled but there is no authentication type and password configured
C. ISIS Area addresses are not configured on both routers
D. L1 wide Metrics are disabled on the routers
E. ISIS Circuit id does not match on Node-1 and Node-2
Answer: C

11. A SDP is created on Node-2 with the far end address set to Node-3. The SDP stays down on Node-2. Based on the following CLI output from Node 2, what is the caused of the problem?
A. No LDP link session between Node 2 and Node 4
B. No LDP link session between Node 4 and Node 3
C. No LDP link session between Node 1 and Node 4
D. No LDP link session between Node 3 and Node 2
E. None of the above
Answer: B

12. Node A has an active BGP route 10.1.1.1 in its routing table, but the same route is not found in Node D routing table. Which of the following configurations are required to resolve this problem?
A. Add Interface X to OSPF on Node B as passive interface
B. Redistribute interface address Y and Z into BGP
C. ISIS Enable route-reflection on Node B
D. Enable next-hop-self on Node C
E. Enable route-reflection on Node C
Answer: AE

免費下載4A0-110考古庫Demo

Pass4Side提供最新的Alcatel Lucent認證 4A0-110考古庫，其全名為：(Alcatel-Lucent Advanced Troubleshooting). 在您決定是否購買之前 可以先下載4A0-110考古庫的部分演示. Pass4side是全球唯一提供所有IT認證考試考古庫demo免費下載的廠商 ，以下為免費4A0-110模擬測試題的下載鏈接

免費的4A0-110考古庫PDF下載鏈接

免費4A0-107考古庫Demo賞析

　
　
Exam : Alcatel-Lucent 4A0-107
Title : Alcatel-Lucent Quality of Service

1. True of False: A proper end-to-end QoS solution is becoming more of an issue even as more bandwidth is being made available to today’s bandwidth-intensive, interactive multimedia applications.
A. True
B. False
Answer: A

2. Which of the following QoS policies does not have a default policy?
A. scheduler policies
B. service ingress
C. service egress
D. network queue
E. network
F. slope
Answer: A

3. Which of the following are Trusted boundaries by default? Choose 2 answers.
A. An IES SAP
B. A VPLS SAP
C. A network port
D. A VPRN SAP
E. An access port
Answer: CD

4. Which of the following are examples of metrics for QoS?
A. delay, jitter, packet loss
B. latency, FIFO, WRED
C. signal degradation, attenuation, line loss
D. SNR, radial CODEC inversion, latency
E. Inverse Queue Depletion, delay, packet loss
Answer: A

5. Which of the following are characteristics of DSCP. Choose 3 answers?
A. Part of the layer 3 header
B. A 6-bit field of which the first 3 bits indicate the IP Precedence bits
C. Specifies 8 different priorities
D. Specifies 3 precedence levels
E. Part of the layer 2 header
F. Specifies 64 different per hop behaviors
Answer: ABF

6. Pick from the following list the 3 major components of the QoS features on the Alcatel-Lucent 7750 SR.
A. virtual inflow classification
B. real-time QoS shaping
C. traffic classification
D. 802.1q p-bit rate-limiting
E. buffer memory management
F. traffic scheduling
Answer: CEF

7. Which of the following statements are true regarding the DSCP bits? Choose 3 answers.
A. The precedence level bits define 4 Assured Forwarding Classes
B. The three least significant bits of the DSCP bits specify the drop probability
C. The 8 bits of the TOS field are used for DSCP
D. To convert DSCP to IP Precedence the three most significant bits are matched
E. DSCP provides for 64 precedence levels with 3 drop probabilities
Answer: ABD

8. Which of the following statement is true with regards to Q-in-Q on the Alcatel-Lucent 7750 SR?
A. Q-in-Q defines a mechanism for encapsulating queued DSCP traffic at the provider edge
B. Q-in-Q is a new protocol that supercedes 802.1p priority-bit mapping in a QoS-aware network
C. The use of either the inner or outer 802.1p bits in the 802.1q frames for QoS classification can be configured on the Alcatel-Lucent 7750 SR
D. Q-in-Q is a protocol which re-encapsulates trunked p-bits in an outer label that is mapped into the EXP bits in an MPLS backbone
E. none of the above
Answer: C

9. Which of the following is not one of the ingress matching criteria for a network policy? Choose all that apply.
A. TCP port numbers
B. LSP EXP
C. DSCP
D. Source and destination IP addresses
E. Dot1P priority
Answer: AD

10. Which of the following are not considered a differentiator/classifier of customer traffic at layer 2 or 3 of the OSI model? Choose all that apply.
A. DSCP
B. 802.1p
C. IP Precedence
D. TCP/UDP Port numbers
E. HTML version
Answer: DE

11. True of False. There is a default network policy applied to all router interfaces?
A. True
B. False
Answer: A

12. Which of the following are not categories of forwarding classes on the Alcatel-Lucent 7750 SR? Choose 3 answers.
A. Real-time
B. Assured
C. Non-conforming
D. High Priority
E. Expedited
Answer: ACE

13. Which of the following are Ethernet SAP encapsulation types? Choose all that apply.
A. Null
B. Dot1Q
C. Q-in-Q
D. IPCP
E. BCP-Null
F. BCPdot1.q
G. Frame Relay
Answer: ABC

14. The IOM is responsible for which of the tasks listed below? Choose 3 answers.
A. local processing of critical control plane functions
B. IPSec VPN hardware accelerated encryption
C. queuing, scheduling, and buffer management
D. IP/MPLS/MAC forwarding lookup
E. Layer 2 / Layer 3 encapsulation
Answer: CDE

免費下載4A0-107考古庫Demo

Pass4Side提供最新的Alcatel Lucent認證 4A0-107考古庫，其全名為：(Alcatel-Lucent Quality of Service). 在您決定是否購買之前 可以先下載4A0-107考古庫的部分演示. Pass4side是全球唯一提供所有IT認證考試考古庫demo免費下載的廠商 ，以下為免費4A0-107模擬測試題的下載鏈接

免費的4A0-107考古庫PDF下載鏈接

免費4A0-108考古庫Demo賞析

　
　
Exam : Alcatel-Lucent 4A0-108
Title : Alcatel-Lucent Multicast Protocols

1. The use of PIM as a multicast routing protocol provides for which one of the following services?
A. Authentication
B. Guaranteed Delivery
C. Device Security
D. Preventing packet forwarding loops
E. Preventing Denial of Service attacks
Answer: D

2. Which MAC address will multicast address 224.128.0.1 translate to?
A. 01-00-5e-80-00-01
B. 01-00-5e-22-41-40
C. 01-00-5e-22-28-01
D. 00-01-5e-80-00-01
E. 01-00-5e-00-00-01
F. 01-01-5e-22-28-01
Answer: E

3. What is the range of addresses allocated for SSM?:
A. 239.0.0.0/8
B. 233.x.y.0/24
C. 224.0.0.0/24
D. 232.0.0.0/8
Answer: D

4. The OUI field of the MAC address for IP multicast frames is:
A. 00-01-5e
B. 01-01-53
C. 01-01-5e
D. 01-00-5e
E. 01-00-53
Answer: D

5. Which of the following are characteristics of the one to many model of multicast data delivery? (Choose two)
A. Receivers are generally unknown by the source
B. Well suited for applications in which the receivers provide feedback to each other and the source
C. There is a single data flow, from the source to the receivers
D. All devices are potentially capable of generating multicast data
E. Receivers are generally known by each other since any receiver may be a source
Answer: AC

6. Choose the answer that best completes the statement: An end station on an Ethernet network receiving an IP multicast packet will:
A. Determine at Layer 1 if it is interested in the frame
B. Determine at Layer 2 if it is interested in the frame
C. Determine at Layer 2 after reading the protocol ID field if it is interested in the frame
D. Determine at Layer 3 if it is interested in the frame
E. Determine at Layer 7 if it is interested in the frame
Answer: B

7. An end station receiving a broadcast packet will always process the data up to which layer of the OSI stack?
A. Layer 1
B. Layer 2
C. Layer 3
D. Layer 4
E. Layer 7
Answer: C

8. Who periodically sends IGMP Host Membership Queries?:
A. The router elected as Querier on a LAN
B. The first host to expire their local suppression timer
C. Only the multicast enabled hosts on a LAN
D. All routers on a LAN
E. All multicast enabled routers on a LAN
Answer: A

9. When forwarding a multicast frame, the normal behavior for a LAN switch with IGMP snooping enabled, is to forward the frame based on the same rules as if it were:
A. A unicast frame with a known destination in the forwarding table
B. A unicast frame with an unknown destination in the forwarding table
C. A unicast frame with a known source in the forwarding table
D. A unicast frame with an unknown source in the forwarding table
Answer: A

10. How many bits of the IP multicast address are copied directly to the multicast MAC address?
A. 27
B. 5
C. 28
D. 9
E. 23
Answer: E

11. Which two of the following addresses should not be used in a multicast network at the same time?
A. 233.44.12.35
B. 234.45.12.35
C. 235.46.12.35
D. 236.174.12.35
E. 237.171.12.35
Answer: CD

12. If IGMP version 1 is in use, when is a Host Membership Report issued?:
A. The report is issued by the routers on the broadcast domain in response to a periodic query
B. The report is issued by all members of the multicast group on the broadcast domain in response to a periodic query
C. The report is issued by the receiver at startup of the multicast application.
D. The report is issued by one member of the group on the broadcast domain in response to a periodic query
E. (a) or (b)
F. (c) or (d)
Answer: F

13. Which two of the following addresses should not be used in a multicast network at the same time?
A. 224.192.12.35
B. 235.182.12.35
C. 226.172.12.35
D. 237.138.12.35
E. 238.64.12.35
Answer: AE

14. Which protocol uses multicast address 224.0.0.22?:
A. PIM version 1
B. IGMP version 2
C. OSPF
D. IGMP version 3
E. PIM version 2
Answer: D

15. Which MAC address will the IP multicast address 239.33.42.107 translate to?
A. 01-00-5e-a1-2a-6b
B. 01-00-5e-21-2a-6b
C. 01-00-5e-21-2c-6c
D. 00-01-5e-a1-2a-6b
E. 00-01-5e-21-2a-6b
F. 01-01-5e-a1-2a-6b
Answer: B

16. A multicast receiver has joined multicast group 224.0.0.1. By default, how often will it issue IGMP Host Membership Reports for this group?
A. never
B. 30 seconds
C. 60 seconds
D. 120 seconds
E. 260 seconds
F. Whenever it receives a Query
Answer: A

免費下載4A0-108考古庫Demo

Pass4Side提供最新的Alcatel Lucent認證 4A0-108考古庫，其全名為：(Alcatel-Lucent Multicast Protocols). 在您決定是否購買之前 可以先下載4A0-108考古庫的部分演示. Pass4side是全球唯一提供所有IT認證考試考古庫demo免費下載的廠商 ，以下為免費4A0-108模擬測試題的下載鏈接

免費的4A0-108考古庫PDF下載鏈接